Content
System Info
System Resourses
- CPU - Load, Temperature, Clock rate, Fan speed
- GPU - Load, Temperature, Clock rate
- RAM - Load, Capacity
- Storage - Capacity
- Network - Download / Upload speed
Fan/Pump Profile
System Specs
CPU, GPU, Motherboard,
RAM, Storage, Audio,
Network specification and
detailed information.
Fan Profile
Customise 8 types of fan
curves to apply settings.
Double click to name the custom curve
The set CPU or GPU temperature
is shown on the chart as a dynamic
vertical green line.
Customized Markers Mode
5 markers to drag the speed
and temperature conditions.
Fixed Speed Mode
Drag the point to set the temperature
and the percentage of RPM.
Select the point and type in the box
to set the temperature and the percentage of RPM.
Apply fan speed settings
to the selected group of fans.
Apply fan speed settings
to all the fans connected
to the selected controller.
Reset to default settings.
Turn on/off the hints.
The fan speed in the diagram
will change according to the fan size.
No matter what the temperature is,
the fan speed will be the same.
Start/ Stop Mode
(Only support fans with this function)
On: The fan will start spinning when reaching the
temperature of the 1st marker.
Off: The fan will always be operating.
Green point
Start/ Stop mode is applied to the set of fan.
Red line
To prevent component damage,
the start temperature must be set below 50 °C.
Start/ Stop Mode
(Only support fans with this function)
On: The fan will start spinning when reaching the
temperature of the 1st marker.
Off: The fan will always be operating.
Green point
Start/ Stop mode is applied to the set of fan.
Red line
To prevent component damage,
the start temperature must be set below 50 °C.
The fan speed in the diagram
will change according to the fan size.
Pass fan speed control to the motherboard.
Note: Please set the corresponding fan header as PWM mode.
The fan speed settings in the software
won't be applicable when the
motherboard RPM sync is on.
Quick Sync Lighting
Motherboard Lighting Sync
Pass the lighting effects control
to the motherboard software
Export: Save all the set values.
Import: Import all the set values
in L-Connect 3.
After importing the data,
please click [ Apply ]
to activate the settings.
Hints:
Turn on/off the hints.
The lighting effects settings in the software
won't be applicable when the motherboard
lighting sync is on.
Independent Fan Utility
Fan lighting effects settings demo with SL-INF.
Hints
Turn on/off the hints.
Export: Save all the set values.
Import: Import all the set values
in L-Connect 3.
After importing the data,
please click [ Apply ]
to activate the settings.
Green point
Start/ Stop mode is applied to the set of fan.
Status of the fan group
- Connected controller (UNI HUB)
port number - The name of the group of fans
(double click to define the name) - The current fan speed
- The current lighting effect
The fan can select the lighting effects
in combined mode or separately
with the fan blade and the fan frame.
Custom the color of the selected palette.
Palette
- Customise each color
(settings will be saved when changing) - Select to fill the color in the box.
Fill in the box to set the LED color.
The box number depends on the lighting effect.
Speed
Set the running speed of the light effect.
Brightness
Set the light effect brightness,
set 0% to turn off light.
Direction
Set the direction of the lighting effect.
Merge Lighting Effects
Select the lighting effects with the merge icon.
The merge mode can merge all the fans connecting to the same
controller and create consistent lighting effects.
On: Lighting effects run through all the fans
Off: Lighting effects run through each fan cluster respectively
Able to respectively set the fan speed
of each fan cluster when [Merge] is on.
GA II Trinity
Redefine your style.Maximize your performance.
The preview animation of Trinity's lighting effects.
Status - displays the current CPU temperature,
Trinity RPM, and lighting effect status.
Style -switch three different Trinity appearance effects,
which are displayed in the preview animation.
Trinity radiator fan and water block pump speed settings.
Select the speed mode. Press the gear icon to edit the detailed settings for that mode.
Trinity water block lighting effect settings.
Modes available: Inner and outer ring combined, Inner ring only + Outer ring only.
Dazzle Mode Style
Dual-Infinity Style
Sink Hole STYLE
Preview animation of RGB devices such as external light strips.
When Sync Trinity RGB is disabled,
you can set the number of LED bulbs
for infinite looping of lighting effects.
When Sync Trinity RGB is enabled,
the lighting effects of external light strips
or RGB devices are synchronized
with the lighting effects of Trinity water block.
When "Sync Trinity RGB" is enabled,
you can set the number of fans for the radiator.
Options include 240mm or 360mm.
GALAHAD II Trinity RGB (GA II Trinity R)
version features an RGB fan
lighting effect animation preview.
GALAHAD II Trinity Performance
Edition fan/Pump speed settings.
Click to edit the radiator fan speed settings.
The devices is GALAHAD II Trinity Performance.
Click to edit the pump speed settings.
Trinity Performance Edition pump has four speed modes:
Quiet, StdSP, and HighSP are manually adjustable fixed speed modes.
PWM is fully automatic and cannot be manually set for speed.
You can manually enter the pump speed value or manually drag the speed node below.
The devices is GALAHAD II Trinity RGB.
Click to edit the pump speed settings.
Trinity RGB Edition pump has two speed modes:
FixRPM is manually adjustable fixed speed modes.
PWM is fully automatic and cannot be manually set for speed.
You can manually enter the pump speed value
or manually drag the speed node below.
Strimer Plus
Type of STRIMER PLUS.
Double-click to define the name.
STRIMER PLUS 24 PIN PIN
has 6 channels of LEDs
(each channel with 2 diffusers)
STRIMER PLUS 3x8 PIN
has 6 channels of LEDs
(each channel with 2 diffusers)
STRIMER PLUS 2x8 PIN
has 4 channels of LEDs
(each channel with 2 diffusers)
Combined Mode
Use the combined lighting effects.
Individual Mode
Can individually set the lighting effect
to each LED channel
Select all the LED channels
The target LED channel and lighting effects
Select 01~06 as the target LED channel,
able to multi-select to set the lighting effect
at the same time.
Click [Apply] to activate the settings
Settings
On: Run L-Connect 3 automatically on system reboot.
Off: Manually start L-Connect 3 on every system reboot.
On: L-Connect 3 minimize to taskbar when close.
Off: Exit L-Connect3 when close.
Language
English / Français / Deutsch / español / 简体中文 / 繁體中文
Temperature display
Celsius / Fahrenheit
Identify the device
Selected device will blink.
Name your device
Suggest naming with position.
e.g. top, front, back.
Fan quantity
Set each set of fan cluster quantity.
Reorder Fan Cluster
Drag the group of fans with
green arrow to switch order for
the merge lighting effects.
(Hardware needs to support this function)
Check the software /
firmware controller version and update /
review version manually.
Auto notification for Update
On: Will notify when there is an updated version of software and firmware.
Off: Manually check the updated version of software and firmware.
Merge Effect Fan Installation Advice
Users can merge all the fans connecting to the same controller and create consistent lighting effects.
Recommend to install as bellow direction to achieve complete lighting effects.
- Mount the fans clockwise:
Recommend mounting the clusters of fans port header in the clockwise order.
SL V2 Merge
SL/AL Merge
- Make sure the order of each cluster of fans is following the order of the lighting effects ( L-Connect 3 > Settings > Devices).
The lighting effects go as 1st >2nd > 3rd > 4th.
New fans (with green arrow), such as SL V2 supports drag to sort the order. Click apply to set.
GA II LCD
GA II LCD硬體確認安裝完成，L-Connect 3 軟體將自動辨識到硬體，請點選左側選單GA II LCD進入控制介面。
點擊偵測到的GA II LCD
GA II LCD - Screen 頁面功能介紹 ( 用於設定LCD螢幕畫面 )
屏幕自訂名稱，點擊兩下可修改
依標籤分別可設定主螢幕LCD，兩側LED燈效，風扇燈效。
屏幕翻轉功能:效果只會在硬體上呈現，使用者安裝角度與預想顯示不一致時，可透過此功能設定調整，每次點擊可轉90度。
風扇速度調整快速選單
LCD螢幕亮度調整
水冷幫浦控制快速選單
LCD螢幕除了可上傳圖片/影片外還內建多款特效，讓您可為螢幕打造最個人化又充滿趣味的最佳體驗
本區依照點選的主題樣式，對應出現可細部調整的選項
點選齒輪設定，使用者可跳至【FAN/Pump Profile】頁面，自訂風扇速度/水冷溫度之自定義選單
GA II LCD Screen 頁面 - 【Image Video 】上傳功能，讓玩家自行客製畫面，將最愛圖片或影片刻錄在螢幕上，還可隨時更換
確認選擇Image Video
- 此選單呈現刻錄於LCD的照片影片，隨選隨換
- 下拉後可依照素材分類，讓玩家快速選取
- 點擊Add按鈕進入下一步
- 點擊Add出現選單
- 拖曳綠色擷取框右下角，可拉大縮小擷取範圍，最小範圍為480x480 pixel(LCD螢幕最佳解析度)
- 拖曳中心點移動，確認擷取位置
- 確認按鍵
- 如不須調色，點選確認匯入螢幕按鈕，即可立刻錄進LCD螢幕
- 如想對匯入的素材圖片/影片做進階編輯，
可選取欲編輯素材，點選【Edit】按鈕，
即可進入進階編輯工具視窗
- 圖片翻轉功能，順時鐘或逆時鐘方向，每按一次轉90度
- 水平鏡射功能，上下或左右翻轉
確認選擇Image Video
- 此選單呈現刻錄於LCD的照片影片，隨選隨換
- 下拉後可依照素材分類，讓玩家快速選取
- 點擊Add按鈕進入下一步
- 點擊Add出現選單
- 影片擷取框，初始框的大小值為匯入影片的480x480 pixel，使用者不能再縮小框(但可拉大範圍)，確保符合硬體最低解析度，避免影像模糊
- 錄影按鈕，尚未有錄影資料時，顯示為不可點擊
- 錄影確認完成鈕
- 錄影最大時間長為3分鐘，錄影暫停時-本區時間碼也為暫停
- 使用者可隨意拖拉縮放想要的影片區塊，
最終軟體都會自動編碼尺寸符合最佳硬體
解析度-480 x 480 Pixel
- 取消擷取按鈕，使用者可退回L-CONNECT 3主程式
- 播放影片按鈕
- 播放影片的總時長與目前時間點
- 目前播放的倍數
- 播放倍數修改按鈕
- 影片播放控制拉桿，使用者可拖拉快速到需要的影片時間點
- 使用者可隨意拖拉縮放想要的影片區塊，
最終軟體都會自動編碼尺寸符合最佳硬體
解析度-480 x 480 Pixel
- 使用者可隨意拖拉縮放想要的影片區塊，
最終軟體都會自動編碼尺寸符合最佳
硬體解析度-480 x 480 Pixel
- 移動綠色擷取框與拖拉範圍，
初步確認想擷取的影片範圍
- 可先點擊播放按鈕或拖拉播放拉桿，確認想要的影片內容與時間點
- 可先把時間點暫停在想要擷取影片的起始點
- 在播放暫停的狀態下，點擊【錄影鈕】
將會【同步啟動錄影截取與播放】，
避免錯失開頭的幾秒鐘；當然您也可
在影片單獨播放時，按下錄影鈕擷取
- 點擊【錄影暫停鈕】，
將會【同步暫停錄影與
播放影片】，避免錄到
暫停影格
- 錄影中時擷取框顯示為紅線框
- 目前累積的錄影時數
- 擷取框可在影片範圍內隨意移動，但不可再改變擷取框大小
- 再次點擊錄影鈕時，即會啟動錄影與播放
- 錄影中或暫停時都可點擊錄影確認鈕，完成錄影擷取
- 點擊Add出現選單
- 點擊Add出現選單
- Loading數值，請稍微等待影片轉碼
GA II LCD Screen 頁面 - 【特效主題】介紹，內建多種特效，玩家可搭配監控水溫，CPU 負載等數據，讓數據轉換為有趣的視覺效果
內建多款特效，並且同樣可結合自己喜愛的圖片、時鐘效果
下雨特效
點選Add
下雨特效
選擇上傳圖片
確認上傳
下雨特效
本區可讓使用者選擇下雨特效時，雨勢的大小是否與電腦水溫/CPU 負載數據相關連結，選擇動態為連結，靜態則由使用者自訂特效的強度
由使用者設定高低數值，當實際硬體數值超過設定值時，將會依照特效，呈現效果強度警示使用者
下雨特效
數位時鐘選項
下雨特效
對應Type選擇，數位時鐘位置、文字顏色、字型等皆可再細部調整
文字顏色以時鐘為例，自左而右分別為日期、時間、AM/FM的顏色設定
字體設定
字體設定
時鐘於或畫面位置的上、中、下設定
時鐘於畫面位置的左、中、右設定
時鐘文字組齊左、齊中、齊右設定
文字的陰影設定
下雨特效
文字的陰影設定
GA II LCD - Screen LED頁面 ( 用於設定LCD螢幕的兩側LED燈條 )
預設燈效為彩虹
本區對應所選的LED燈條效果，對應出現可再進一步細部調整的選項
螢幕兩側的LED燈條燈效設定
內建多達17種燈效設定，每個燈效都可由玩家再進行細部設定
GA II LCD - Fan LED 頁面介紹 ( 用於設定風扇燈效 )
選擇此設定可與 Screen LED 同步速度與燈效效果
本區對應所選的燈效，可再進一步細部調整的選項
風扇燈效設定
內建多達6種燈效設定，每個燈效都可由玩家再進行細部設定
支援非聯力燈效設備功能 :
連同非聯力的燈珠設備數量加總統計，於此填入總LED燈珠數量，燈效將可延伸控制非聯力燈效設備
Note: Please set the corresponding
fan header as PWM mode.