Content

System Info

System Info Resourse

System Resourses

  • CPU - Load, Temperature, Clock rate, Fan speed
  • GPU - Load, Temperature, Clock rate
  • RAM - Load, Capacity
  • Storage - Capacity
  • Network - Download / Upload speed
System Info Specs

System Specs
CPU, GPU, Motherboard,
RAM, Storage, Audio,
Network specification and
detailed information.

Fan/Pump Profile

Fan-Pump ProfileSL 2

Fan Profile
Customise 8 types of fan
curves to apply settings.

Double click to name the custom curve

The set CPU or GPU temperature
is shown on the chart as a dynamic
vertical green line.

Customized Markers Mode
5 markers to drag the speed
and temperature conditions.

Fixed Speed Mode

Drag the point to set the temperature
and the percentage of RPM.

Select the point and type in the box
to set the temperature and the percentage of RPM.

Apply fan speed settings
to the selected group of fans.

Apply fan speed settings
to all the fans connected
to the selected controller.

Reset to default settings.

The fan speed in the diagram
will change according to the fan size.

Fan-Pump Profile-SL-Fixed

Start/ Stop Mode
(Only support fans with this function)
On: The fan will start spinning when reaching the
temperature of the 1st marker.
Off: The fan will always be operating.

Green point 
Start/ Stop mode is applied to the set of fan.

Red line
To prevent component damage,
the start temperature must be set below 50 °C.

Fan-Pump ProfileSL-INF-Start-Stop 2

Start/ Stop Mode
(Only support fans with this function)
On: The fan will start spinning when reaching the
temperature of the 1st marker.
Off: The fan will always be operating.

Green point 
Start/ Stop mode is applied to the set of fan.

Red line
To prevent component damage,
the start temperature must be set below 50 °C.

The fan speed in the diagram
will change according to the fan size.

MB RPM Sync

Pass fan speed control to the motherboard.
Note: Please set the corresponding fan header as PWM mode.

The fan speed settings in the software
won't be applicable when the
motherboard RPM sync is on.

Quick Sync Lighting

Apply lighting effects across all devices with in one page, or sync all via motherboard software.

Motherboard Lighting Sync
Pass the lighting effects control
to the motherboard software

Export: Save all the set values.
Import: Import all the set values
in L-Connect 3.
After importing the data,
please click [ Apply ]
to activate the settings.

Hints:
Turn on/off the hints.

The lighting effects settings in the software
won't be applicable when the motherboard
lighting sync is on.

Independent Fan Utility

Fan lighting effects settings demo with SL-INF.

SL Infinity Lighting Page03
Controller Tab

Hints
Turn on/off the hints.

Export: Save all the set values.
Import: Import all the set values
in L-Connect 3.
After importing the data,
please click [ Apply ]
to activate the settings.

Green point
Start/ Stop mode is applied to the set of fan.

Status of the fan group

  • Connected controller (UNI HUB)
    port number
  • The name of the group of fans
    (double click to define the name)
  • The current fan speed
  • The current lighting effect

The fan can select the lighting effects
in combined mode or separately
with the fan blade and the fan frame.

Custom the color of the selected palette.

Palette

  1. Customise each color
    (settings will be saved when changing)
  2. Select to fill the color in the box.

Fill in the box to set the LED color.
The box number depends on the lighting effect.

Fill in all boxes with the same selected color.
Restore to the default palette.

Speed
Set the running speed of the light effect.

Brightness
Set the light effect brightness,
set 0% to turn off light.

Direction
Set the direction of the lighting effect.

AL Fan Lighting Page –02

Merge Lighting Effects
Select the lighting effects with the merge icon.
The merge mode can merge all the fans connecting to the same
controller and create consistent lighting effects.
On: Lighting effects run through all the fans
Off: Lighting effects run through each fan cluster respectively

Able to respectively set the fan speed
of each fan cluster when [Merge] is on.

Strimer Plus

Type of STRIMER PLUS.
Double-click to define the name.

STRIMER PLUS 24 PIN PIN
has 6 channels of LEDs
(each channel with 2 diffusers)

STRIMER PLUS 3x8 PIN
has 6 channels of LEDs
(each channel with 2 diffusers)

STRIMER PLUS 2x8 PIN
has 4 channels of LEDs
(each channel with 2 diffusers)

Combined Mode
Use the combined lighting effects.

Individual Mode
Can individually set the lighting effect
to each LED channel

Clear all selection

Select all the LED channels

The target LED channel and lighting effects
Select 01~06 as the target LED channel,
able to multi-select to set the lighting effect
at the same time.
Click [Apply] to activate the settings

Settings

Setting-general

On: Run L-Connect 3 automatically on system reboot.
Off: Manually start L-Connect 3 on every system reboot.

On: L-Connect 3 minimize to taskbar when close.
Off: Exit L-Connect3 when close.

Language
English / Français / Deutsch / español / 简体中文 / 繁體中文

Temperature display
Celsius / Fahrenheit

Setting - Device V2

Identify the device
Selected device will blink.
Name your device
Suggest naming with position.
e.g. top, front, back.

Fan quantity
Set each set of fan cluster quantity.

Reorder Fan Cluster
Drag the group of fans with
green arror to switch order for
the merge lighting effects.
(Hardware needs to support this function)

Setting-Update

Check the software /
firmware controller version and update /
review version manually.

Auto notification for Update
On: Will notify when there is an updated version of software and firmware.
Off: Manually check the updated version of software and firmware.

Merge Effect Fan Installation Advice

Users can merge all the fans connecting to the same controller and create consistent lighting effects. 
Recommend to install as bellow direction to achieve complete lighting effects.

  1. Mount the fans clockwise:
    Recommend mounting the clusters of fans port header in the clockwise order.

SL V2 Merge

MergeInstall_SLV2_2

SL/AL Merge

MergeInstall_others_2
  1. Make sure the order of each cluster of fans is following the order of the lighting effects ( L-Connect 3 > Settings > Devices).
    The lighting effects go as 1st >2nd > 3rd > 4th.
    New fans (with green arrow), such as SL V2 supports drag to sort the order. Click apply to set.
Setting - Device V2