Content
L-Wireless SYNC
Please note the following before set up:
- Each computer supports only one L-Wireless SYNC wireless controller.
- LCD fans and LED fans can be mixed and matched in the same group.
- One controller supports up to 10 channels and 6 types of product firmware.
- One channel supports up to 3 LCD fans / 4 LED fans.
- Supports binding of up to 3 Strimer Wireless cables.
First enter the wireless device binding page - L-Wireless SYNC Setup
Tap the icon and the hardware will light up yellow
so you can confirm your device.
Click on the icon for hardware binding,
and then click again for unbinding.
This is the IP of the controller, which matches
the IP of the bonded device, and is the correct
bonding status.
Each computer is limited to one controller,
and one controller can bind up to 10 groups
of channels.
Click on the icon to change the name
for easy confirmation of the device.
If there is any interference problem with
other devices after bonding, you can manually
switch the wireless channel again.
Click and go to Using Wireless Devices
IP of the original binding controller
If you are sure you are ready to bind the
device, you can click this icon to restore
the device to its normal unbound state.
The red status indicates that this device
has been bound by another controller
and the original controller is not online at the moment.
SL Wireless Fan
SL Wireless Fan Utility - Lighting Effects
Click on the product control page
The bonded device grouping
is selected here for setup.
Device Settings page, default settings
for lighting effects
Wireless Device Sequencing Setting:
When in QuickSYNC and MERGE lighting
modes, the lights will flow in sequence.
SL Wireless Fan Utility - LCD Screen
Tap to set the screen，If the LCD cannot
be selected, please reboot the computer.
Default screen placement is upright
with power cables facing up.
If the hardware placement is not straight by
default, please click on the group rotation
function to align the wires so that the direction
shown is the same as the actual direction of the
hardware placement.
Grouping of screens allows video
images to be displayed across screens.
Menu selections to put in sensors,
pictures, and videos
Uploading clips to the media library
If the screen cannot be set, you can try to restart
the LCD, it takes about 10 seconds to restart,
after clicking the screen will blink and pop up the
linkage icon, it means it has been restarted.
SL Wireless Fan Utility - Fan profile
Fan/Pump Profile setting page.
to the same series of fans.
Strimer Wireless
Lighting Setting Page
you can set the light effect for each light
bar separately and customize the light
effect by yourself.
light bar is selected.
set for each light bar
devices so that supported lighting
can flow in sequence
to present the light effect.
effect, click and select the color.
TL Wireless Fan
TL Wireless Fan Utility - Lighting Effects
Click on the product control page
The bonded device grouping
is selected here for setup.
Device Settings page, default settings
for lighting effects
Wireless Device Sequencing Setting:
When in QuickSYNC and MERGE lighting
modes, the lights will flow in sequence.
TL Wireless Fan Utility - Lighting Effects - Upper and Lower Lighting Switching on Hardware
Please click the [Apply] button to take effect, the up/down
lighting effect will be exchanged continuously when it is
turned on, including the application of the up/down lighting
effect afterwards (Clicking the Apply to All TLW button has
no effect on this setting).
TL Wireless Fan Utility - LCD Screen
Tap to set the screen，If the LCD cannot
be selected, please reboot the computer.
Default screen placement is upright
with power cables facing up.
If the hardware placement is not straight by
default, please click on the group rotation
function to align the wires so that the direction
shown is the same as the actual direction of the
hardware placement.
Grouping of screens allows video
images to be displayed across screens.
Menu selections to put in sensors,
pictures, and videos
Uploading clips to the media library
If the screen cannot be set, you can try to restart
the LCD, it takes about 10 seconds to restart,
after clicking the screen will blink and pop up the
linkage icon, it means it has been restarted.
TL Wireless Fan Utility - Fan profile
the wind speed setting.
Fan/Pump Profile setting page.
to the same series of fans.
System Info
System Resourses
- CPU - Load, Temperature, Clock rate, Powers, Voltages
- GPU - Load, Temperature, Clock rate, Powers, Voltages
- RAM - Load, Capacity
- Storage - Capacity
- Network - Download / Upload speed
After clicking on the item, the details
will appear again in the right column.
The new floating system monitor allows you to easily glance at important hardware information.
The floating system monitor window is
on by default but can be turned off here.
Click on it to call up the L3 main software
to the upper level of the window.
Background Transparency Toggle Button
Temporarily close the window button,
it will appear again when you restart
the L3 main software.
Preset monitor grid.
Can be customized.
Towable
Drag the edge to zoom in & out
Fan/Pump Profile
Note: The PWM 4P cable from the receiver must be
connected to the motherboard to perform this function.
Fan Profile
Customise 8 types of fan
curves to apply settings.
Double click to name the custom curve
The set CPU or GPU temperature
is shown on the chart as a dynamic
vertical green line.
Customized Markers Mode
5 markers to drag the speed
and temperature conditions.
Fixed Speed Mode
Drag the point to set the temperature
and the percentage of RPM.
Select the point and type in the box
to set the temperature and the percentage of RPM.
Apply fan speed settings
to the selected group of fans.
Apply fan speed settings
to all the fans connected
to the selected controller.
Reset to default settings.
Turn on/off the hints.
The fan speed in the diagram
will change according to the fan size.
No matter what the temperature is,
the fan speed will be the same.
Start/ Stop Mode
(Only support fans with this function)
On: The fan will start spinning when reaching the
temperature of the 1st marker.
Off: The fan will always be operating.
Green point
Start/ Stop mode is applied to the set of fan.
Red line
To prevent component damage,
the start temperature must be set below 50 °C.
Start/ Stop Mode
(Only support fans with this function)
On: The fan will start spinning when reaching the
temperature of the 1st marker.
Off: The fan will always be operating.
Green point
Start/ Stop mode is applied to the set of fan.
Red line
To prevent component damage,
the start temperature must be set below 50 °C.
The fan speed in the diagram
will change according to the fan size.
Pass fan speed control to the motherboard.
Note: Please set the corresponding fan header as PWM mode.
The fan speed settings in the software
won't be applicable when the
motherboard RPM sync is on.
Quick Sync Lighting
Motherboard Lighting Sync
Pass the lighting effects control
to the motherboard software
Export: Save all the set values.
Import: Import all the set values
in L-Connect 3.
After importing the data,
please click [ Apply ]
to activate the settings.
Hints:
Turn on/off the hints.
SIGNALRGB support, this feature is under development.
Wireless products do not support
motherboard light synchronization.
(W*) This symbol indicates that the
light effect works across all wireless devices.
The lighting effects settings in the software
won't be applicable when the motherboard
lighting sync is on.
Settings
On: Run L-Connect 3 automatically on system reboot.
Off: Manually start L-Connect 3 on every system reboot.
On: Displays a floating system information window
Off: The Floating Monitor Information window will be closed until this option is manually opened.
On: Hide on system tray when auto run on boot
Temperature display
Celsius / Fahrenheit
On: L-Connect 3 minimize to taskbar when close.
Off: Exit L-Connect3 when close.
Language
English / Français / Deutsch / español / 简体中文 / 繁體中文
When the hardware and software lose communication,
click this button to reopen the background server, after
clicking it will automatically open and close the software,
when the software opens automatically, please wait for
about 3 minutes for the background server to re-serialize
the hardware and software.
All wireless devices are integrated here
Lighting direction setting:
Only for QuickSYNC and MERGE.
Device Sequencing Setting:
When in QuickSYNC and MERGE lighting
modes, the lights will flow in sequence.
Switch to the wireless
device bonding page.
Number of fans per channel
The hardware lights up yellow after clicking
to identify the use of the channel.
Check the software /
firmware controller version and update /
review version manually.
Auto notification for Update
On: Will notify when there is an updated version of software and firmware.
Off: Manually check the updated version of software and firmware.
Software and firmware window alerts for updates,
click to update the latest software and firmware.
After checking, please click to download
After the update is complete, please restart your computer to finish the update.
the wind speed setting.